Brick Paver Installation & Edging



Staging of material

Many paver tasks will vary depending upon access, website conditions, job size and naturally, the weather. These scenarios can have a general impact on your project from a timing stand point. Mindful consideration needs to be taken to figure out the time to start the paver installation. Constantly try to avoid any traffic or decrease on the prepared locations.

The foreman or task manager must always have the products (sand/ pavers) distributed around the job site for easy and effective setups. Paver pallets/bundles should be put in a way not to disrupt the paver installation. The correct pallet/bundle placement can make the actual job installation much easier and quicker by decreasing the general labor of managing the material.

Brick paver patterns

Pavers can be put in several patterns depending on their shape. Each paver shape will normally have several different hatch patterns that are supplied by the manufacturer.

The laying pattern and shape of the paver is extremely important to the performance of the application. Professionals need to consider the traffic weight loads on their paver projects. 90 or 45 degree herringbone patterns are suggested in all street and driveway applications, as these patterns will offer the optimum load support needed and will withstand sneaking from the turning of tires and braking or starting of automobile traffic. In most applications worldwide, it has actually been revealed that pavers laid in a herringbone pattern have performed effectively.

Pavers that are 60 mm (2 - 3/8 in) density are suitable for pedestrian applications. Pavers that are going to be utilized in industrial or industrial applications need to be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a number of conditions that figure out the beginning point of a paver project.

When starting to install pavers it is best to snap a real straight chalk line on the surface of the bed linen sand or pull a true straight string line above the surface of the bedding sand at the completed elevation of the pavers This will assist as a guide for keeping straight joint lines and will also allow the installer to make modifications in the positioning of the pavers.

Structures and concrete suppressing are generally not straight and ought to not be used for developing straight joint lines. The usage of string lines is essential to determine the true straightness of the edge. As the paver installation advances, the string lines will assist lessen the requirement for small trim pieces.

These will preserve a minimum joint width and enable the bed linen and jointing sand to go into in between each paver. Pavers with spacer bars are usually not laid in snug versus each other since a string line will provide consistent joint spacing.

Installation of brick pavers.

One of the most widely utilized approaches for the installation of pavers is hand installation of each paver. It is best to set up a single row of pavers along one of the real straight lines that you have actually pulled or above the bedding sand. The best method is to place a paver versus another one and let it move down into the bed linen sand.

When setting up pavers on a high grade, they must be installed at the base of the grade going uphill. This will prevent the pavers from creeping as they are being laid.

On large commercial and industrial applications, hand laying pavers would not be cost effective due to the labor strength. The very best method for setting up pavers on big jobs is to install them mechanically. The use of a mechanical laying machine can install approximately 6000 - 7000 sq ft a day. There are a couple products a specialist need to think about prior to setting up pavers mechanically:

1.) Mechanical installers are only capable of installing pavers in particular patterns.

2.) The specialist should ensure that the manufacturer is capable of production and bundling pavers in the wanted pattern on the pallets for simple mechanical installation.

3.) Professionals may encounter a color blending scenario coming off the packages of pavers Poor color blending could result in an irregular looking installation. The majority of makers follow color blending on each bundle of pavers, however it is the specialist's obligation to guarantee proper mixing in the field.

Cutting procedures for brick pavers.

Specialists generally have two methods of cutting pavers. When cutting pavers wet, it will assist lessen dust and will extend the diamond blades life. The operator of the brick saw should constantly cut the pavers away from the surface area of the paver field when cutting wet, due to the reality that the pavers will produce a slurry that will stain the paver surface.

The brick saw operator must always use the appropriate protection that is required for operating a saw, such as Tree Service Del Ray Beach eye, ear, breathing and hand security ).

Edging types

Edge restraints play a major function in the general success of an interlocking pavement installation Edging restraints remove lateral motion of the pavers and hold the pavers tightly together. Specifically at the outer border of the paver application, without an edging restraint, your job is guaranteed to stop working over time.

There are numerous different edging restraints from which specialists can select. Typically produced edge restraints are the most commonly utilized by contractors. Made edging restraints can range from, plastic edging, steel and aluminum, lumbers or precast concrete and stone. An edging type that is used mostly in industrial and commercial applications is poured-in-place concrete curbs. This edging restraint is usually installed by other specialists.

Edging installation.

This might result in the migration of the bed linen sand and eventual lateral movement of the pavers. If there is a possibility of losing bed linen sand in between the pavers and the edge restraint, then geo textile fabric is suggested. When a space between the pavers and the edging surpasses 3/8" (10mm), then the area should be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers need to be compacted. The whole area that is to be compacted must be swept tidy of any foreign objects and particles that can trigger scratching or scuffing on the surface of the pavers.

It is very important to have a compactor that can apply between 3000lbs. And 5000 lbs. Of centrifugal compaction force. In addition, it is necessary that the first compaction occurs prior to any jointing sand has actually been applied to the pavers. If jointing sand is applied to the pavers before compaction occurs, this can trigger a bridging problem and will not enable the joints to be totally filled with jointing sand. This can likewise avoid the pavers from being effectively set into the bedding sand.

When condensing the pavers, it is advised that you make a minimum of two passes in different directions throughout the pavers. This will permit the pavers to be properly set in the bedding sand and will force the bed linen sand up into the joints from the bottom of the pavers.

The compaction of the pavers is really important to the final performance of the pavers. Failure to do appropriate compaction can lead to contortions and pavement failure with time.


Paver pallets/bundles should be placed in a manner not to interfere with the paver installation. One of the most commonly utilized approaches for the installation of pavers is hand installation of each paver. The operator of the brick saw need to always cut the pavers away from the surface of the paver field when cutting wet, due to the truth that the pavers will produce a slurry that will stain the paver surface area. Edging restraints remove lateral motion of the pavers and hold the pavers securely together. When a space between the pavers and the edging exceeds 3/8" (10mm), then the space ought to be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *